Current Category
Garden Poly fittings

Click on the sub-categories below:   All of our Antelco low-density poly fittings are made in Australia.

	13mm Poly Joiner 13mm Low density poly x 13mm Low density poly barbed joiner, requires 2 x poly clamps or Cobra clips to make the connection secure.		Price:	QTY:

	13mm Poly Elbow Poly x poly elbow used for making 90 degree turns.		Price:	QTY:

	13mm Poly Tee Poly x poly x poly Tee.		Price:	QTY:

	13mm End Plug End plugs are used to close the end of a poly line.   All fittings including plugs must be secured to the poly using a clamp.		Price:	QTY:

	13mm In-Line Filter In-Line filters must be installed wherever micro sprays, drippers or micro sprinklers are to be used.   Ideally, you should install a 25mm plastic disk filter at the tap but the in-line filters will be fine if you have very clean town water.		Price:	QTY:

	13mm In-Line Tap Our in-line taps are used in the low-density poly line to provide a manual isolation.   This is particularly usefull in greenhouses and fern hot houses.		Price:	QTY:

	13mm Poly Clamp Poly ratchet clamps should be used on all low-density poly fittings to ensure that the tube stays on the barbed fitting.		Price:	QTY:

	13mm Poly x Click-On Connector This item connects 13mm low-density poly pipe directly to a standard Click-On tap connection.   Make sure that you use a 13mm stainless steel Cobra clip to hold the poly pipe.		Price:	QTY:

	13mm x 3/4" Director Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.		Price:	QTY:

	13mm x 1" Director Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.		Price:	QTY:

	13mm x 1/2" Female Threaded Elbow Poly x 1/2" female threaded elbows are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above the ground.		Price:	QTY:

	13mm x 1/2" male Elbow Poly x 1/2" male elbow used to provide water to a pop-up spray or riser outlet.		Price:	QTY:

	13mm x 1/2" Female Threaded Tee Poly x 1/2" female threaded tees are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above the ground.		Price:	QTY:

	13mm x 1/2" male Tee Poly x 1/2" male x poly tee used to provide water to a pop-up spray or a riser with a spray outlet on top.		Price:	QTY:

	CAPO Rubber Grommet 13mm ID for XPANDO fittings The CAPO rubber grommet is used with XPANDO 13mm fittings to allow for the easy and secure attachment of 13mm tube to polyethylene and PVC supply pipes for irrigation systems.   The 13mm ID CAPO suits the 16mm Antelco drill bit (code 10151845).		Price:	QTY:

	XPANDO 13mm inlet x 13mm Take-Off XPANDO 13mm fittings to allow for the easy and secure attachment of 13mm tube to polyethylene and PVC supply pipes for irrigation systems.   Requires a CAP 10145735 Grommet.		Price:	QTY:

	19mm Poly Joiner Used to join 19mm poly to 19mm poly and to make fast and secure repairs.   Make sure that you use a clamp or Cobra clip.		Price:	QTY:

	19mm Poly Elbow Poly x poly elbow used for making 90 degree turns.		Price:	QTY:

	19mm Poly Tee Poly x poly x poly Tee.		Price:	QTY:

	19mm End Plug End plugs are used to close the end of a poly line.   All fittings including plugs must be secured to the poly using a clamp.		Price:	QTY:

	19mm In-Line Filter In-Line filters must be installed wherever micro sprays, drippers or micro sprinklers are to be used.   Ideally, you should install a 25mm plastic disk filter at the tap but the in-line filters will be fine if you have very clean town water.		Price:	QTY:

	19mm In-Line Tap Our in-line taps are used in the low-density poly line to provide a manual isolation.   This is particularly usefull in greenhouses and fern hot houses.		Price:	QTY:

	19mm Poly Clamp Poly ratchet clamps should be used on all low-density poly fittings to ensure that the tube stays on the barbed fitting.		Price:	QTY:

	Reducing Joiner, 19mm to 13mm This is just like the standard joiner except it has different sized ends.   One side takes the larger 19mm poly pipe and the other side takes the smaller 13mm.		Price:	QTY:

	Reducing Tee 19mm x 13mm The reducing tees are used where a branch line needs to be smaller than the main.		Price:	QTY:

	19mm Poly x Click-On Connection This item connects 19mm low-density poly pipe directly to a standard Click-On tap connection.   Make sure that you use a 19mm stainless steel Cobra clip to hold the poly pipe.		Price:	QTY:

	19mm x 3/4" Director Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.		Price:	QTY:

	19mm x 1" Director Directors are used to connect low-density poly pipe onto solenoid valves and any other female BSP fitting.		Price:	QTY:

	19mm x 1/2" Female Threaded Elbow Poly x 1/2" female threaded elbows are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above the ground.		Price:	QTY:

	19mm x 1/2" male Elbow Poly x 1/2" male elbow used to provide water to a pop-up spray or riser outlet.		Price:	QTY:

	19mm x 3/4" male Elbow Poly x 3/4" male elbow used to provide water to a pop-up spray or riser outlet.		Price:	QTY:

	19mm x 1/2" Female Threaded Tee Poly x 1/2" female threaded tees are used to install an articulated riser for a pop-up sprinkler/spray or, to install a 1/2" male riser so that a larger spray or sprinkler can be mounted well above the ground.		Price:	QTY:

	19mm x 1/2" male Tee Poly x 1/2" male x poly tee used to provide water to a pop-up spray or a riser with a spray outlet on top.		Price:	QTY:

	19mm x 3/4" male Tee 19mm Poly x 3/4" male x poly tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.		Price:	QTY:

	19mm x 1/2" male Corner Elbow This is a great item.   Used to provide water to a pop-up spray or sprinkler when it is to be located in the corner of the yard.		Price:	QTY:

	CAPO Rubber Grommet 19mm ID x 19mm XPANDO fittings The CAPO rubber grommet is used with XPANDO 19mm fittings to allow for the easy and secure attachment of 19mm or 25mm tube to polyethylene and PVC supply pipes for irrigation systems.   The 19mm ID CAPO suits the 22mm Antelco drill bit (code 10151865).		Price:	QTY:

	XPANDO 19mm inlet x 19mm Take-Off XPANDO 19mm fittings to allow for the easy and secure attachment of 19mm tube to polyethylene and PVC supply pipes for irrigation systems.   Requires a CAP 10145755 Grommet.		Price:	QTY:

	25mm Poly Joiner 25mm barbed joiners are used to join a further length of 25mm poly to an existing length as well as making repairs easier and faster.   Remember to use clamps with these fittings to prevent the pipe blowing off the fitting.		Price:	QTY:

	25mm Poly Elbow 25mm barbed poly elbows are used to make a 90 degree turn in the poly pipe and so prvent any kinking, make sure that you use clamps with this fitting.		Price:	QTY:

	25mm Poly Tee 25mm poly tees are used to provide an off-take for another 25mm poly line, make sure that you use clamps with these fittings.		Price:	QTY:

	25mm End Plug End plugs are used to close the end of a poly line.   All fittings including plugs must be secured to the poly using a clamp.		Price:	QTY:

	25mm In-Line tap Our in-line taps are used in the low-density poly line to provide a manual isolation.   This is particularly usefull in greenhouses and fern hot houses as well as any other irrigation system.		Price:	QTY:

	25mm Poly Clamp Poly ratchet clamps should be used on all low-density poly fittings to ensure that the tube stays on the barbed fitting.		Price:	QTY:

	Cobra Clip for 25mm Low Density Poly Pipe C27/8 - Each Cobra Clips are full stainless steel clips used to provide a permanent and drip-proof connection for poly pipe to poly fittings.   Excellent value for money, extremely long life and ease of application are 3 of the many popular benefits of the Cobra clip.   The clamp is placed around the pipe with the fitting inserted and simply "Clipped" tight with the installation tool or a pair of multigrips.   The price here is for INDIVIDUAL clamps.		Price:	QTY:

	Reducing Joiner, 25mm x 13mm This is just like the standard joiner except it has different sized ends.   One side takes the larger 25mm poly pipe and the other side takes the smaller 13mm.		Price:	QTY:

	Reducing Joiner, 25mm x 19mm This is just like the standard joiner except it has different sized ends.   One side takes the larger 25mm poly pipe and the other side takes the smaller 19mm.		Price:	QTY:

	Reducing Tee 25mm x 13mm Branch The reducing tees are used where a branch line needs to be smaller than the main.		Price:	QTY:

	Reducing Tee, 25mm x 19mm Branch The reducing tees are used where a branch line needs to be smaller than the main.		Price:	QTY:

	25mm x 3/4" BSP Director Directors are used to connect 25mm low-density poly pipe onto 3/4" female BSP solenoid valves and any other female BSP fitting.		Price:	QTY:

	25mm x 1" BSP Director Directors are used to connect 25mm low-density poly pipe onto 1" female BSP solenoid valves and any other female BSP fitting.		Price:	QTY:

	25mm x 1/2" Female Threaded Elbow 25mm poly x 1/2" female BSP elbow used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.		Price:	QTY:

	25mm x 1/2" Female Threaded Tee 25mm poly x 1/2" female BSP tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.		Price:	QTY:

	25mm x 1/2" male Elbow 25mm poly x 1/2" male BSP elbow used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.		Price:	QTY:

	25mm x 3/4" male Elbow 25mm poly x 3/4" male BSP elbow used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.		Price:	QTY:

	25mm x 1/2" male Tee 25mm poly x 1/2" male BSP tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.		Price:	QTY:

	25mm x 3/4" male Tee 25mm poly x 3/4" male BSP tee used to provide water to a pop-up spray, sprinkler or a riser with a spray outlet on top.		Price:	QTY:

	XPANDO 19mm inlet x 25mm Take-Off XPANDO 19mm fittings to allow for the easy and secure attachment of 25mm tube to polyethylene and PVC supply pipes for irrigation systems.   Requires a CAP 10145755 Grommet.		Price:	QTY: